Legrand RFB9 Bedienungsanleitung PDF herunterladen

RFB 119 Series Floor Box

I N S T A L L A T I O N I N S T R U C T I O N S

Installation Instruction No.: 1 003 189R1 – Updated April 2011

Products Covered: Floor Box Cat. Nos.: RFB9, RFB11,

Floor Box Covers: RFB119CTC, RFB119BTC

Floor Box Device Plates: RFB119 (suffix)

CAUTION: Do not operate tile stripper or resurfacing equipment over top of covers. This may result in damage to the surface finish

of the product.

CAUTION: When used in bare concrete or terrazzo floors, use part number: RFB119-PAN (Sold separately).

CAUTION: Box has no post pour adjustment.

Step 1 Locate and position box in accordance to floor

plans or blueprint.

6 5/16"

[161mm]

[

178mm]

14"

[356mm]

12 5/8"

[321mm]

Step 2 Level & anchor box. Top of box must be flush with

concrete pour. Use screws, nails, or wire to prevent

box from floating during pour.

Step 3 Remove mudcap and attach conduit.

Step 4 Reinstall mudcap.

Legrand/Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Legrand/Wiremold electrical

products may bear the mark of a Nationally Recognized Testing

Laboratory (NRTL) and should be installed in conformance with current

local and/or the National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

NOTE: For use in bare concrete or terrazzo floors, replace

mudcap with part number: RFB119-PAN. (Sold

separately.) (See Step 19.)

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - RFB 119 Series Floor Box

RFB 119 Series Floor BoxI N S T A L L A T I O N I N S T R U C T I O N SInstallation Instruction No.: 1 003 189R1 – Updated April 2011Products Cove

Seite 2

2KO between compartmentsGrommet (not supplied)Step 5 Screed to top of box surface. Hand troweling recommended near box edges.Step 7 If service access

Seite 3

3Step 10 Determine device plate selection based on sizes illustrated below.7/8"[22mm]4 1/2"[114mm]Spacer PlateCat No. RFB119-SPACERUsed to c

Seite 4

4Step 11 Determine device plate required to close off wiring compartments. Sectional (1-13/16" [46mm] wide) or standard deviceplates may be used

Seite 5

5Step 12 Mount blanking plates and spacers between standard size plates to close off any gaps or openings. Typical layouts areillustrated below.6-GANG

Seite 6 - CARPET INSTALLATIONS

6CARPET INSTALLATIONSStep 13 Install carpet and cut 12 1/16" x 10 5/16" [262mmx 306mm] rectangular opening over box opening.Step 14 Open cov

Seite 7 - CARPET INSERT TEMPLATE

7CARPET INSERT TEMPLATECAUTION: When printing copies ofthis template please besure template is scaledcorrectly and is the correct size once it is pri

Seite 8 - TILE INSTALLATIONS

TILE INSTALLATIONSStep 17 Cover flange is 1/4" thick. Use 1/8" spacer, Cat.No. RFB119-TS, for 3/8" tile installations. Use twospacers f

Verwandte Modelle: RFB11 | RFB119CTC | RFB119BTC | RFB119 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand RFB9 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand RFB9 herunter. Legrand RFB9 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: RFB11 | RFB119CTC | RFB119BTC | RFB119 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand RFB9