Legrand AV3 Bedienungsanleitung PDF herunterladen

Products Covered: AV3STC, AV3ATC, AV3ARTTC, AV3CTC, AV3CRTTC, AV3SHTC, AV3ATC-LJB,

AV3ARTTC-LJB, AV3ATCLJB25 & AV3ARTTCLJB25.

CAUTION DO NOT operate tile stripper or resurfacing equipment over top of covers. This may result in damage to the

surface finish of the product.

Suitable for use in air handling spaces in accordance with Sec. 300-22 (C) of the National Electrical Code.

AV3 Poke-Thru Series

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 003 904 – April 2004

Walker

electrical systems conform to and should be properly grounded

in compliance with requirements of the current National Electrical Code

or codes administered by local authorities.

All electrical products may present a possible shock or fire hazard if

improperly installed or used. Walker electrical products may bear the

mark as UL Listed and/or Classified and should be installed in

conformance with current local and/or the National Electrical Code.

24" [610mm] Min

Center – Center

[178mm]

CAUTION: Be certain to drill hole at least 4" [102mm] from any wall or

pillar to leave enough room for Poke-Thru cover assembly.

CAUTION: For tile installations up to a maximum of

3/4" [19.1mm] thick.

NOTE: For tile thickness greater than 3/4" [19.1mm]

consult factory.

IMPORTANT: Please read all instructions

before beginning.

CAUTION: Spacing is limited to no more than one hole per each

65 sq. ft. [6 sq. m] of floor area in each span.

Step 2 Remove 7" dia. [178mm] section from carpet

or tile. Use template provided.

Step 1 Layout and locate position of hole(s).

Step 3 Core drill hole.

CAUTION: Poke-Thru cannot be rotated in

hole after insertion into floor.

4" [102mm] Diameter Core Drill

4 1/16" [103mm] Actual Diameter

Push Down

#6-32 x 1/4" FHMS

three (3) required

Step 4 Stem Assembly:

Catalog No. AV3STC

Insert stem into hole.

Step 5 Cover Assembly:

Catalog No. AV3CTC.

Remove disposable plate

and replace with carpet/tile

flange. Install with three (3)

#6-32 x 1/4" [6.4mm] FHMS.

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - AV3 Poke-Thru Series

Products Covered: AV3STC, AV3ATC, AV3ARTTC, AV3CTC, AV3CRTTC, AV3SHTC, AV3ATC-LJB, AV3ARTTC-LJB, AV3ATCLJB25 & AV3ARTTCLJB25.CAUTION DO NOT operat

Seite 2

CONVENTIONAL WIRING SCHEMATIC ISOLATED GROUND WIRING SCHEMATICBLACK or HOT BLACK BLACK or HOT BLACKFrom branch circuit from Poke-Thru receptacle From

Seite 3

3Extron Device(Not Supplied)CAUTION: Empty communication ports must be closed off with foam blocks, TracJack blanks or Extron Single and/or Double MAA

Seite 4

4Slide Cover Mounting ScrewsTwo (2) #6-32Align gasket overreceptacle andpress bead intoflange channel.Push DownOnce Poke-Thru is pushedinto the Cored

Seite 5

The AV3TC Series Poke-Thru Devices are UL Listed and Classified to U.S. and Canadian safety standards to the following conditions:The AV3STC Poke-Thru

Seite 6 - Carpet Cutout Template

The Wiremold Company U.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-2