Legrand WIUC20GL Bedienungsanleitung PDF herunterladen

WHILE-IN-USE COVER DESCRIPTION

This product is a weatherproof cover that is intended to enclose an

electrical device (outlet, GFCI, switch, etc.) and protect the device

from inclement weather even when a plug and cord are inserted in it.

It is designed to install quickly and easily (see instructions below) and

provide an attractive, durable finish that will yield long-lasting results.

APPLICATION

The cover should be installed in areas subject to saturation from water

or other liquids, (see description for “Wet Location” and “Damp

Location” in the National Electrical Code). The cover can be mounted

horizontally or vertically, as long as the hinge is in the top corner. See

Figure 1 (A-D) for applicable mounting and attachment options. The

cover includes multiple plates, so it can be used to cover different

types of electrical devices.

WARNING - Turn off all power to circuit before installing this

device. Improper wiring of any electrical device can cause seri-

ous injury or death. These wiring devices should only be

installed by an Electrician or other qualified person.

CAUTION - This cover should be installed in accordance with the

National Electrical Code, and all applicable local codes and standards.

INSTALLATION INSTRUCTIONS

NOTE: The cover should be installed on a smooth, flat, non-porous

surface. To install on an irregular surface, use a proper amount of

caulking to ensure a watertight seal between the back of the cover

and the mounting surface.

1. Disconnect power to circuit by removing fuse or turn circuit breakers

to OFF before installing.

2. Remove the existing receptacle cover, if any, and discard.

3. Back off the mounting screws that hold the GFI or receptacle to

the junction box but do not remove screws.

4. Insert mounting screws through the keyhole shaped mounting holes

on assembly and slide the assembly to the left (see Figure 2).

Center the device in the box. Tighten screws.

5. If mounting to an FS or outdoor junction box use the four screws

provided to further secure the assembly to the box.

6. DO NOT OVER TIGHTEN SCREWS.

7. Choose appropriate wall plate and snap in by putting one long

edge in place first and rotating the plate over the device. (If device

is in the way, loosen screws and move left or right.) Discard

other plate(s).

8. For best rain protection, be sure to route cords through the cord

outlet and press the cover firmly until it snaps closed. Position

cord gaskets as shown in Figure 3.

LIMITED ONE YEAR WARRANTY

Pass & Seymour will remedy any defect in workmanship or material in Pass & Seymour products which

may develop under proper and normal use within one year from date of purchase by a consumer:

(1) by repair or replacement, or, at Pass & Seymour's option, (2) by return of an amount equal to

consumer's purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such

remedy by Pass & Seymour does not include or cover cost of labor for removal or reinstallation of the

product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL

DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES

INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or

limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion

may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE

LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations

on how long an implied warranty lasts, so the above limitation may not apply to you.)

To insure safety, all repairs to Pass & Seymour products must be made by Pass & Seymour, or under

its specific direction. Procedure to obtain performance of any warranty obligation is as follows:

(1) Contact Pass & Seymour, Syracuse, New York 13221, for instructions concerning return or repair;

(2) return the product to Pass & Seymour, postage paid, with your name and address and a written

description of the installation or use of the Pass & Seymour product, and the observed defects or

failure to operate, or other claimed basis for dissatisfaction.

TradeMaster

WEATHERPROOF WHILE-IN-USE COVER

INSTALLATION INSTRUCTIONS

Figure 1

A B

Figure 2 Figure 3

1 2

TradeMaster 1

Inhaltsverzeichnis

Seite 1 - TradeMaster

WHILE-IN-USE COVER DESCRIPTIONThis product is a weatherproof cover that is intended to enclose anelectrical device (outlet, GFCI, switch, etc.) and pr

Seite 2

DESCRIPCIÓN DE TAPA DURANTE SU USOEste producto es una tapa a prueba del tiempo que está diseñadapara encerrar un dispositivo eléctrico (enchufe, GFCI

Verwandte Modelle: WIUC20CL | WIUC20WL | WIUC10DGL | WIUC10DCL | WIUC10DWL | WIUC10SG | WIUC10SC | WIUC10SW | WIUC10SB | WIUC10CL | WIUC10GL | WIUC10WL |

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand WIUC20GL Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand WIUC20GL herunter. Legrand WIUC20GL User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: WIUC20CL | WIUC20WL | WIUC10DGL | WIUC10DCL | WIUC10DWL | WIUC10SG | WIUC10SC | WIUC10SW | WIUC10SB | WIUC10CL | WIUC10GL | WIUC10WL |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand WIUC20GL