Legrand WC Cellular Raceway Risers Bedienungsanleitung PDF herunterladen

1. Field cut opening in raceway

(see Fig. 1 for LHT Risers and

Fig. 2 for LT Risers).

2. Install grommets in holes. Remove

all sharp edges exposed to wires.

3. Install void closure for WCR2 and

WCR3. For WCR1 and WCR1EE,

tape to close off opening between

raceway and riser. For WCR1, tape

sides to close off opening between

raceway and riser.

4. Pop rivet or fillet weld riser in place.

Exposed screw threads are not

allowed inside of raceway.

Figure 1 – LHT Riser

Figure 2 – LT Riser

Terminal Bushing.

Extension CBRE-LT, CBR1ELT.

CBR1

WCR1EE (Shown)

Opening Spacing

Same for WCR1.

7" [178mm] WCR1 and WCR1EE

8" [203mm] for WCR2 and WCR3.

Field Cut Openings:

CBR-LT Cut Two 2 1/2" x 6" Openings.

CBR1-LT Cut Two 2" x 5 1/2" Openings.

Tape for WCR1 Only.

Tape

Extension CBRE-P.

CBR.

WCR2 (Shown).

Void Closure

(Two Required).

3 1/2 " [89mm] for WCR1 and WCR1EE

4" [102mm] for WCR2 and WCR3.

Field Cut Openings: CBR-LHT

Cut Three 2 1/2" x 6" [64mm x

152mm] Openings. CBR1-LHT

Cut Three 2" x 5 1/2" [51mm x

140mm] Openings.

4 1/8"

[105mm]

3 1/2"

[89mm]

[

762mm]

3 1/2"

[89mm]

30"

[762mm]

[152mm]

12" [305mm] CBR

10" [ 254mm] CBR1

12" [305mm] CBR

10" [254mm] CBR1

CBR & HDR Series Risers

I N S T A L L A T I O N I N S T R U C T I O N S

Installation Instruction No.: 1 000 591R1 – Updated March 2010

Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Wiremold electrical products

may bear the mark as UL Listed and/or Classified and should

be installed in conformance with current local and/or the National

Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

1 2

Inhaltsverzeichnis

Seite 1 - CBR & HDR Series Risers

1. Field cut opening in raceway (see Fig. 1 for LHT Risers and Fig. 2 for LT Risers). 2. Install grommets in holes. Remove all sharp edges exposed to

Seite 2 - Figure 4 – HDR Riser

Figure 3 – HT RiserFigure 4 – HDR RiserTerminal Bushing.Extension CBRE-P.For CBR and CRB14 1/8" [105mm].Field Cut Openings:CBR-HT Cut One 2 1/2&q

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand WC Cellular Raceway Risers Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand WC Cellular Raceway Risers herunter. Legrand WC Cellular Raceway Risers User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand WC Cellular Raceway Risers