Legrand Wide Slide Series Incandescent Dimmers Bedienungsanleitung PDF herunterladen

7. Restore power. To change the mini-

mum speed, DISCONNECT POWER

FROM CIRCUIT, and remove the

wall plate. Use a small insulated, flat

tipped screwdriver to adjust the trim

pot, which is accessible via the slot

(marked CALIBRATION) provided on

the strap. Turn up to increase the

minimum speed setting. Next, mount

the wall plate back and restore the

power. NOTE: Never adjust trim pot

when circuit is live.

NOTE: A 0.3A minimum load is required. It is normal for the control to feel

warm during operation. Use a separate neutral wire for each phase of a

multiphase system containing a dimmer, and for high power single phase

applications where flickering is present.

WARRANTIES

Lifetime Warranty. The device you have purchased is warranted under normal

use against defects in workmanship and materials for as long as you own the

device. If the device fails due to manufacturing defect during normal use, return

the device for replacement to the store where purchased or send to:

Pass & Seymour Legrand

50 Boyd Avenue

Syracuse, NY 13209

All requests for replacement must include a dated sales receipt (legible copies

acceptable).

ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO A PERIOD OF TWO YEARS FROM THE

DATE OF PURCHASE. YOUR SOLE AND EXCLUSIVE REMEDY AGAINST

PASS & SEYMOUR LEGRAND UNDER ANY WARRANTY SHALL BE THE

EQUIVALENT REPLACEMENT OF THE DEVICE. IN NO EVENT SHALL ANY

WARRANTY APPLY TO ANY DEFECT ARISING OUT OF ANY ALTERATION

OF THE DEVICE, IMPROPER WIRING, IMPROPER INSTALLATION, MISUSE,

ABNORMAL USE OR NEGLIGENCE. IN NO EVENT SHALL PASS &

SEYMOUR LEGRAND BE LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL,

EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states

do not allow limitations on how long implied warranties last and do not allow

exclusion or limitation of incidental or consequential damages. Some of the

above limitations or exclusions may not apply to every purchaser.

Para ser instalado por electricista certicado u otra persona capacitada.

ADVERTENCIA: Para prevenir una sacudida eléctrica severa o electrocución,

siempre CORTE la electricidad en el panel de servicio antes de instalar esta

unidad, trabajar en el circuito, o cambiar una lámpara.

AVISO: Para reducir el riesgo de recalentamiento y los posibles daños a otro

equipo, no lo instale para controlar un tomacorriente, una lámpara o tubo

fluorescente, o un electrodoméstico alimentado por un transformador. Use

este mando solo con venti ladores que indican que son apropiados para uso

con mandos de velocidad de ventiladores de estado sólido.

Cualquier número de ventiladores pueden ser controlados por un solo mando

de velocidad de ventiladores dado que la suma de las tasas de amperaje de

los ventiladores no exija la tasa de amperaje del mando del ventilador.

No conecte al reductor de luz a otra fuente de potencia que no sea solo

120VAC, 60Hz.

Solo utilice cables de cobre.

Nota: Puede entrar yeso, polvo o pintura y dañar este dispositivo. No

instalar este dispositivo hasta después de haber instalado y pintado la

pared.

INSTRUCCIONES:

1. Si se suministró un kit de cambio de color, y se desea un color diferente, vea

el Procedimiento de Cambio de Color; de lo contrario, proceda al paso #2.

2. Corte la electricidad al circuito en el panel quitando el fusible o APAGANDO

el interruptor automático antes de la instalación.

3. Quite la chapa de pared y los tornillos de montura de chucho, hale el

chucho existente de la caja embutida en la pared.

4. Desconecte el chucho existente del circuito. Instalación de tres direcciones:

Identifique el cabe “COMÚN” (el cable conectado al la terminal marcada

“común – common” o la terminal colorada con un color singular). Para

instalación “nueva” identifique el cable conectado al la fuente de potencia

o a la carga.

5. Conecte el controlador de velocidad del ventilador como mostrado en el

diagrama de instalación utilizando alambre trenzado o sólido #12 o #14 AWG

de cobre. Pele el alambre utilizando la guÌa en la parte trasera del aparato.

INSTRUCCIONES DE INSTALACIÓN

Serie Perilla Deslizable Ancha

CONTROLES DE VELOCIDAD DEL VENTILADOR

INSTRUCCIONES EN ESPAÑOL

LEA Y GUARDE ESTAS INSTRUCCIONES

To be installed by a certied electrician or other qualied person.

WARNING – To prevent severe shock or electrocution, always turn power OFF at the

service panel before installing this unit, working on the circuit, or changing a lamp.

CAUTION – To reduce the risk of overheating and possible damage to other

equipment, do not install to control a receptacle, a fluorescent light or bulb,

or a transformer-supplied appliance. Use this control only with fans that are

marked as suitable for use with solid-state fan speed controls.

Any number of fans may be controlled by a single fan speed control provided

the sum amperage rating of the fans does not exceed the amperage rating of

the fan control.

Do not connect fan control to power source other than 120VAC, 60 Hz only.

Use copper wire only.

Note: Sheet rock, dust and paint can enter and damage this device. This

device should be installed after sheet rocking and painting are completed

COLOR CHANGE PROCEDURE/PROCÉDURE DE CHANGEMENT DE

COULEUR/PROCEDIMIENTO DE CAMBIO DE COLOR

DIRECTIONS

1. If a color change kit was provided, and a different color is desired, see the

Color Change Procedure, if not proceed to step #2.

2. Disconnect power to circuit at the panel by removing fuse or turning circuit

breakers OFF before installing.

3. Remove wall plate and switch mounting screws, pull existing switch from

wall box.

4. Disconnect existing switch from circuit. 3-way installation: Identify the

“Common” wire (wire connected to the terminal marked common or odd

colored terminal). For “new” installation identify wire connected to power

source or to the load.

5. Connect fan speed control as shown in the installation diagram using #12

or #14 AWG stranded or solid copper conductors. Strip wire using gauge

on back of device.

INSTALLATION DIAGRAM FOR SPEED CONTROLS

6. Install fan speed control in wall box, with word ‘TOP’ on the strap right side

up, using mounting screws provided.

Trim

Potentiometer

INSTALLATION INSTRUCTIONS

Wide Slide Series

FAN SPEED CONTROLS

READ AND SAVE THESE INSTRUCTIONS!

1 2

Inhaltsverzeichnis

Seite 1 - Wide Slide Series

7. Restore power. To change the mini-mum speed, DISCONNECT POWER FROM CIRCUIT, and remove the wall plate. Use a small insulated, flat tipped screwdri

Seite 2 - Série à large curseur

DIAGRAMA DE INSTALACIÓN PARA CONTROLES DE VELOCIDAD 6. Instale el controlador de velocidad del ventilador en una caja de pared con la palabra “TO

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand Wide Slide Series Incandescent Dimmers Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand Wide Slide Series Incandescent Dimmers herunter. Legrand Wide Slide Series Incandescent Dimmers User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand Wide Slide Series Incandescent Dimmers