Legrand HA5202 Bedienungsanleitung PDF herunterladen

INSTRUCTION / INSTALLATION SHEET

TVDI Expander for Unity Integration

Module (P/N HA5202)

IS-0457 Rev. O

301Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

1. Introduction

The HA5202 TVDI Expander Module (see Figure 1)

provides the ability to expand beyond two, the

number of TVDI Control Interfaces supported on the

Unity HA6001 Integration Module. Each HA5202

supports four directly connected TVDI Control

Interfaces and is able to be cascaded once, so that

two TVDI Expander Modules may be associated with

one HA6001 Integration Module for support of up to

eight TVDI Control Interfaces. (see Figure 2).

2. Description

• Provides one RJ45 jack for connection to an LCD/TV Display Interface jack on the Unity System Integration

Module.

• Provides one RJ45 jack for cascading up to two total TVDI Expander Modules.

• Provides four RJ45 jacks for connection to individual TV Display Interfaces.

• The first TVDI Expander Module is powered by the attached Integration Module. Any TVDI Expander Modules

connected via the Cascade jack require a 24VDC Power Supply, as power is not passed over the Cascade

connection (see Figure 2).

3. Installation

Installation of the Legrand HA5202 and related components is best accomplished at multiple times during new

construction, at “Rough-in” before the drywall is installed, and at “Trim-out” after the drywall is installed and painted.

IMPORTANT: Read the manuals that are included with all associated Unity products before installation of

any single component. If you are unsure of any of the following installation procedures contact Legrand

Technical Support @ 1-800-321-2343 option 1 or contact a Legrand installer.

A. “Rough-in” steps:

1. HA5201-xx: Run a Category 5 cable from each (up to 4) TV Display Interface (HA5201-xx)

location to the enclosure housing the HA5202.

B. “Trim-out” steps:

NOTE: Make sure that the 24VDC Power Supply is not connected to the HA5202 Module.

1. Install the HA5202/s in the enclosure by first attaching it to the included bracket using the four

corner plungers. Then insert the bracket tabs into the slots on the left of the enclosure and use

the bracket push-pin to secure the HA5202/s to the enclosure.

2. Terminate all Category 5 cables from the TV Display Interfaces with RJ-45 plugs using the T568A

wiring standard, and plug them in to the TVDI RJ45 jacks labeled 1-4 on the HA5202/s.

Figure 1

1 2

Module (P/N HA5202) 1

Inhaltsverzeichnis

Seite 1 - Module (P/N HA5202)

INSTRUCTION / INSTALLATION SHEETTVDI Expander for Unity Integration Module (P/N HA5202) IS-0457 Rev. O 301Fulling Mill Road, Suite G Middletown, PA 17

Seite 2

INSTRUCTION / INSTALLATION SHEETTVDI Expander for Unity Integration Module (P/N HA5202) IS-0457 Rev. O 301Fulling Mill Road, Suite G Middletown, PA 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand HA5202 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand HA5202 herunter. Legrand HA5202 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand HA5202