Legrand 364725-xx Bedienungsanleitung PDF herunterladen

1. Introduction

OnQ Amplified Combo Modules provide a structured method for distributing

telephone service and RF (cable TV) off air signals throughout a residence.

OnQ Amplified Combo Modules can be mounted in OnQ Service Center

Enclosures and come in several different telecom combinations; an example

(12+8) is shown in Figure 1 to the right.

2. Description

The “video” portion of the module has vertical access “F” style fittings for

connecting incoming and outgoing cables, as well as power.

NOTE: The Video module is a 5-1000 MHz amplifier with typically 4.0 dB

of gain per output port and an insertion loss of typically -1.0 dB in the

5-42 MHz range.

The “telecom” portion provides an RJ45 modular jack or 110 punchdown

block for connecting and distributing incoming telephone service to room

locations. Also provided on some configurations is a modular jack labeled

“Security” for interfacing to security systems.

NOTE: The OnQ Combo Module has a vertical dimension of 5 inches.

A total of 7 inches of enclosure space is required for coax cabling.

3. Installation

A. Mounting in Enclosure (refer to Figure 2).

1) Align tabs on the module with slots on rail enclosure.

2) Insert tabs by angling module away from the back of the

enclosure.

3) Rotate the module and insert fasteners on module into

corresponding holes on rail of enclosure. (Plunger must be in

a pulled position for fastener to engage hole.).

4) Push plunger in to lock module in place. Pull on module to

ensure module is locked properly in place.

B. Service Connection - Video Portion (refer to Figure 3).

1) Identify incoming service cable(s) and route to “Cable In” fit-

ting(s) on module.

2) Attach an RG-6 “F” connector to the cable. Connect to fitting

on module and finger-tighten.

C. Service Connection - Telecom Portion

1) Identify incoming service cable and route to RJ45 jack or 110

punchdown block labeled “Line In”.

2) Trim the cable to allow at least three (3) inches of excess

cable.

3) Terminate the cable with an EZ-RJ45 modular plug

(P/N 364554-01, not included) if applicable. Be sure to use

proper terminating tool (P/N 364555-01 per IS-0177). If using

110 punchdown block, insert leads and terminate using

punchdown tool (P/N 363293-01, not included).

OnQ Technologies, Inc.

P.O. Box 60907

Harrisburg, PA 17106-0907

800-321-2343

www.onqtech.com

Installation/Instruction Sheet

OnQ Amplified Combo Module

IS-0266 Rev. O

IS-0266 Rev. O Page 1 of 2

Figure 2

Figure 3

Figure 1

1 2

Inhaltsverzeichnis

Seite 1 - IS-0266 Rev. O

1. IntroductionOnQ Amplified Combo Modules provide a structured method for distributingtelephone service and RF (cable TV) off air signals throughout

Seite 2

D. Terminating the Outlet Cables1) Route the cable to the RJ45 Jack or 110 punchdown block on the module.2) Trim the cable to allow at least three (3

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand 364725-xx Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand 364725-xx herunter. Legrand 364725-xx User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand 364725-xx