Legrand 2000 Series Aluminum Plugmold Multioutlet System Bedienungsanleitung PDF herunterladen

Plugmold 2000 Aluminum

Plugmold 2000TR Aluminum

I N S T A L L A T I O N I N S T R U C T I O N S

Installation Instruction No.: 1 009 949 – February 2011

Legrand/Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Legrand/Wiremold electrical

products may bear the mark of a Nationally Recognized Testing

Laboratory (NRTL) and should be installed in conformance with current

local and/or the National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

AL2000 SYSTEM PRODUCT APPLICATIONS

TO INSTALL:

1. Bring Feed into Base

a. Remove appropriate 1/2" trade size entrance knockout in base, or attach Feed End Fitting (AL2010A).

2. Install Base Section on Surface

a. Attach base section on mounting surface using AL2003 Spring Mounting Clips, or by drilling 9/32” holes in the base and use #8

set screws. Ensure holes are free from burrs.

b. If required, cut base to length and carefully debur any cut ends before mounting. If cuts have been made to the base, center the

cover section over the mounted base. Locate, mark and cut the cover ends. If the edge of any receptacle falls closer than 1 1/2"

[38mm] from the end of the unit, that receptacle must be cut out to allow sufficient space for the installation of an end fitting.

c. Connect multiple sections together using coupler (AL2001). To install, slide coupling plate into both base sections, center on joint

and tighten locking screws.

d. To install around corners, use appropriate elbows, (AL2011 - 90° Flat Elbow), (AL2017 – Internal Elbow), or (AL2017 - External Elbow)

3. Install Ground Adapter

a. Use Ground Adapter (AL2009) provided to secure ground connection. To relocate, loosen set screw and twist counter clockwise.

Position in between receptacles (to avoid interference) and assemble in reverse order.

4. Install Blank End Fitting (AL2010B)

a. At end of base raceway run, slide blank end fitting in last base sections and secure in place by tightening screw.

5. Connect wired section to feed

a. Connect feed wires to wired raceway sections. It is recommended to stagger connection points to allow room for all connections.

6. Snap raceway cover onto base

a. If necessary, snap receptacle harness into cover making sure to line up receptacle faces with pre-punched holes in the raceway cover.

b. Engage lower edge of cover over the edge of the base. Starting at one end and progressing along the unit, snap in upper edge

of the cover with the heel of the hand. Ensure that wires are pushed completely into the base before assembling the cover to

avoid pinching the wires.

7. Snap on cover clip to cover joint seams where lengths of covers come together.

8. To remove cover, insert removal tool into groove, push down and twist.

NOTE: All mounting methods must result in flush interior surface.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Plugmold 2000TR Aluminum

Plugmold 2000 Aluminum Plugmold 2000TR Aluminum I N S T A L L A T I O N I N S T R U C T I O N SInstallation Instruction No.: 1 009 949 – February

Seite 2

AL2010A Feed End FittingAL2010B Blank End FittingAL2043 In-line ReceptacleAL2043TR Tamper-Resistant In-line ReceptacleAL2043IG In-line Isolated Ground

Seite 3

AL2038 Series Round Fixture BoxAL2044 SeriesDeep Device BoxAL2047 Series Shallow Switch &Receptacle BoxTO INSTALL:1. Attach back plate to 2x4 outl

Seite 4 - AL2051H Box Adapter

AL2000B BaseTo attach AL2000B base sections to mounting surface, drill9/32" holes in the base (approx. 48" o.c.). Fasten base with#8 flathea

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand 2000 Series Aluminum Plugmold Multioutlet System Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand 2000 Series Aluminum Plugmold Multioutlet System herunter. Legrand 2000 Series Aluminum Plugmold Multioutlet System User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand 2000 Series Aluminum Plugmold Multioutlet System