Legrand RFB2 Bedienungsanleitung PDF herunterladen

RFB2, RFB2-SS, RFB2-OG

Recessed Floor Box

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 006 179 – September 2006

Wiremold / Legrand electrical systems conform to and should be

properly grounded in compliance with requirements of the current

National Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Wiremold / Legrand electrical

products may bear the mark as UL Listed and/or Classified and should

be installed in conformance with current local and/or the National

Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

BEFORE CONCRETE POUR:

NOTE: Box is supplied with tunnel bracket, tunnel blocks

and device mounting brackets installed. If the

same service is to be used in both compartments,

it will be necessary to remove one or both of the

tunnel blocks to allow for pass-through of the

service wiring. The tunnel blocks are accessible

by removing the tunnel support. The installer may

do this either pre- or post-pour.

Step 1. Determine box location and conduit layout. Remove

box cover and desired knockouts and attach

appropriate conduit adapters, (not supplied by

Wiremold) to steel base.

Step 2. Re-attach box cover to base with (2) #8-32 x 1/2" long

screws provided.

Step 3. Adjust height of box so that the top of the black

trim ring is approximately 1/16" below the concrete

screed line.

Step 4. Secure the box to the floor using wire or other

fasteners through the holes provided in the top

cover. Once positioned, connect conduit to adapters

previously attached to box.

Step 5. Insert mud cap into top opening and press down

firmly to secure. Box is now ready for pour.

WARNING: Pour concrete to 1/16” (1.6 mm) above box

housing. Pours of 1/4” (6.4 mm) or more

over box housing will make it difficult to

break out the mud cap and cause excessive

concrete spalling.

Tunnel Blocks

Tunnel Support

Top of Plastic

Trim Ring

Adjusting

Screws

This box and activations are UL listed for use with tile, terazzo, carpet covered concrete

floors, and floors of wood construction.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Recessed Floor Box

RFB2, RFB2-SS, RFB2-OGRecessed Floor BoxINSTALLATION INSTRUCTIONSInstallation Instruction No.: 1 006 179 – September 2006Wiremold / Legrand electric

Seite 2 - AFTER CONCRETE POUR:

AFTER CONCRETE POUR:NOTE: This box and activation are UL Listed for use withtile, terrazzo, and carpet covered concrete floors,and also wood floors.NO

Seite 3 - WOOD FLOOR INSTALLATION:

WOOD FLOOR INSTALLATION:Step 1. Determine box location and orientation.Step 2. Cut a 6" [152mm] x 7 1/4" [184mm] opening in wood floor.Step

Seite 4

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-

Verwandte Modelle: RFB2-SS | RFB2-OG | FP-CTR | RFB2EXT | RFB2-AAP | RFB2B | RFB2RT | RFB22AB | RFB2GFI | RFB2DP |

Kommentare zu diesen Handbüchern

Keine Kommentare

Legrand RFB2 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Legrand RFB2 herunter. Legrand RFB2 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: RFB2-SS | RFB2-OG | FP-CTR | RFB2EXT | RFB2-AAP | RFB2B | RFB2RT | RFB22AB | RFB2GFI | RFB2DP |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Legrand RFB2